Korg ARP Odyssey Duophonic Synthesizer with SQ-1 Sequencer

- 70 % Off

$34,024.20

Korg ARP Odyssey Duophonic Synthesizer with SQ-1 Sequencer

Add to wishlist
SKU: 3UTAQNFY5F Category: Tags: , , , , , , , , , , ,

Description

ARP Odyssey Duophonic Synthesizer Features:

  • 2VCO. The duophonic design allows two different pitches to sound when you play two notes.
  • The high degree of pitch stability for which the ARP Odyssey was remarkable in its time has been perfectly reproduced.
  • Pitch is variable over a wide range of 20 Hz–2 kHz
  • Pitch modulation and pulse width modulation can be controlled.
  • Oscillator sync provides sharp, great-sounding overtones extending into a high range.
  • Noise generator provides two noise types: white and pink.
  • Powerful LFO can be used as a modulation source for the oscillator or filter, or as a trigger source for sample & hold.
  • Ring modulator generates metallic sounds with rich overtones.
  • The distinctive S/H MIXER lets you easily create sample & hold sounds by using the oscillator or noise generator as a source that’s triggered by the LFO or keyboard.
  • The three types of low-pass filter found on different production runs of the original ARP Odyssey are all provided. With a single switch you can select any one of these filters with their differing characteristics: TYPE I (Rev1) is a 12 dB/octave filter with a sharp and punchy sound, TYPE II (Rev2) is a 24 dB/octave filter that’s great for thick low sounds, and TYPE III (Rev3) features excellent stability even when the resonance is increased.
  • A wide variety of modulation sources such as S/H, LFO, ADSR, and AR can be used to modulate the filter.
  • A high-pass filter is provided following the low-pass filter, giving you even broader sound design possibilities.
  • A new function, the DRIVE switch generates extreme and aggressive sounds.
  • VCA GAIN slider leaves the note sustaining. Ideal for sound design.
  • Envelope generator with two types: ADSR and AR. This can be used not only for the VCA but also to modulate the filter or oscillator.
  • The original PPC (Proportional Pitch Control) based on a rubber pad has been reproduced. Press the rubber pad with your finger to control pitch bend or vibrato depth in proportion to the pressure.
  • A portamento slider and transpose switch are provided. You can also use a switch to select either of the ways in which Rev1 and Rev2/3 of the original ARP Odyssey differ as to whether portamento is applied the moment that you operate the transpose lever.

Connectors:

  • Two types of audio output jack are provided: 1/4″ phone and XLR.
  • External audio input jack is provided, allowing you to process sound from an external device.
  • Headphone jack with adjustable volume is provided. By connecting the headphone jack to the external audio input jack, you can apply self-feedback to generate powerful sounds.
  • CV, GATE, and TRIG jacks are provided, letting you send or receive analog signals to operate the instrument. If you connect the GATE OUT jack to the TRIG IN jack, the EG will not be triggered, allowing you to play legato.
  • Both 1/4″ size and mini-size patch cables are included
  • MIDI IN connector and USB MIDI port are provided, allowing connection to a PC or MIDI device.

Specifications:

Maximum Polyphony : 2 voices for duophonic; normally monophonic ControllersTranspose Positions : 2 octaves down, normal, 2 octave up Proportional Pitch Controlb (Pitch down) Pad: about -2 / 3 octave– (Modulation) Pad# (Pitch-up) Pad: about +2 / 3 octave Noise Generator : Noise Spectrum Types (white and pink) Portamento

  • Maximum Speed : about 0.01 msec./oct
  • Minimum Speed : about 1.5 sec./oct

VCO (Voltage Controlled Oscillator)

  • Waveforms : Sawtooth, Square, Pluse (Dynamic Pluse)
  • Frequency Range : VCO-1 in low freq. mode, 0.2 Hz – 20 Hz: VCO-1 and VCO-2 (audio range) about 20 Hz – 20 kHz
  • Warm Up Drift : 1/30 semitone from turn on max
  • Pulse Width :  50 % – 5 %
  • Pulse Width Modulation : ADSR, +45 % / LFO, +15 %
  • Voltage Controlled Response : 1 V/oct

Maximum Frequency Shifts

  • LFO sin wave, +1/2 oct.
  • LFO square wave, +1.5 oct.
  • ADSR, +9 oct.
  • S/H, +2 oct.

* VCO-1 is low note priority, VCO-2 is high note priority. VCF (Voltage Controlled Filter)

  • Types : Low pass (I: 12 dB/oct., II III: 24 dB/oct.)
  • Frequency Range : 16 Hz – 16 kHz
  • Maximum Usable Q : 30
  • Resonance : 1/2 – self oscillate

Voltage Controlled Response : C3 key (left edge): 0 V / C6 key (right edge) 3 V VCA (Voltage Controlled Amplifier)Dynamic Range : 80 dB Ring Modulator

  • Type : Digital
  • Input Signal : VCO-1, VCO-2 (square wave)

Sample & Hold

  • Command Sources : Keyboard or LFO trigger
  • Sampled Signals : VCO-1 sawtooth wave and square wave, VCO-2 square wave and pink noise

ADSR Envelope Generator

  • Attack Time : 5 msec. – 5 sec.
  • Decay Time : 10 msec. – 8 sec.
  • Sutatin Level : 0 – 100 % or Peak
  • Release Time : 15 msec. – 10 sec.

AR Envelope Generator

  • Attack Time : 5 msec. – 5 sec.
  • Release Time : 10 msec. – 8 sec.

Control Input Jacks

  • Pedal : 6.3 mm monaural phone jack
  • Portamento Foot Switch : 6.3 mm monaural phone jack
  • Audio Output Jacks : LOW
  • Connector : 6.3 mm monaural phone jack
  • Maximum Output Level : -20 dBu@ 10 k ohm load
  • Output Impedance : 10 k ohm
  • Audio Output Jacks : HIGH
  • Connector : XLR connector
  • Maximum Output Level : +4 dBu@ 1 k ohm load
  • Output Impedance : 330 ohm

Headphones Jack

  • Connector : 6.3 mm stereo phone jack
  • Maximum Output Level : 50 mW + 50 mW@ 33 ohm load
  • Output Impedance : 10 ohm (* Controllable by volume knob.)

External Audio Input (Ext Audio Input) Jack

  • Connector : 6.3 mm monaural phone jack
  • Maximum Input Level : -10 dBu
  • Input Impedance : 22 k ohm

MIDI Connector : INUSB Connector : Type B CV IN/OUT Jacks

  • Keyboard CV (IN/OUT) : 1 V/oct.
  • Connector : 3.5 mm monaural phone jack

GATE IN/OUT Jacks

  • GATE IN : +3 V (minimum)
  • GATE OUT : +10 V, key down; 0 V all keys up
  • Connector : 3.5 mm monaural phone jack

TRIG IN/OUT Jacks

  • TRIG IN : +3 V pulse min., 10 µsec. Duration minimum
  • TRIG OUT : +10 V pulse on key depression, 10 µsec. Duration
  • Connector : 3.5 mm monaural phone jack

Power Supply : AC adapter jack (DC 9V) 

Power Consumption : 6.5 W 

Dimensions (W x D x H) : 496 x 265 x 89 mm / 19.53” x 10.43” x 3.50” 

Weight : 3.7 kg / 8.16 lbs 

Design Variations : White (ARP ODYSSEY Module Rev1), Black and Orange (ARP ODYSSEY Module Rev3) 

Included Items : AC adapter, phone cable, mini-phone cable

 

SQ-1 Sequencer Features:Various sequencer mode.The SQ – 1 has 8 – step sequencers of A and B total of 2 channels, which not only operate in order but also have various modes. For example, you can operate in sequence of A and B, use it as a sequencer of 16 steps in total, operate randomly ignoring the order, operate in parallel while controlling different parameters of A and B, etc. from a simple sequence From complicated variations, you can choose from a variety of modes depending on the application.Volca direct step editing with excellent improvisation.2 x 8 step buttons enable powerful performance as volca like playing the sequence itself by switching the function with the MODE button besides on / off of pronunciation which is a general usage . You can create effects like short loops and irregular rhythms in “active step” which skips step in the middle of sequence and “step · jump” which instantly reproduces only step being pressed . Also, if you control the synth bass with “Slide” which can produce effects like step-to-step connection, anyone can easily produce acid sound.Robust compact body, battery operated.SQ-1 condensed carefully selected functions adopted a compact but very firmly made sheet metal body. Aligning with the MS – 20 series, even a heavy feeling drifts as if it was made in the same era. In addition to two AA batteries, the power supply also drives with USB bus power.Other Features.

  • Resolution of sequence step can be set from quarter note, eighth note, sixteenth note. 
  • It is possible to set the method of controlling the pitch with the step knob. Knob values ​​You can pronounce with the same pitch, or change to the major, minor, or chromatic scale that is closest to the value of the knob.

SQ-1 Sequencer Specifications:

  • Sequencer mode ALTERNATE, ORDER, PARALLEL TURN, PARALLEL ORDER, CV / DUTY, CV / SLIDE, CV / DUTY | RANDOM, RANDOM Step mode GATE ON / OFF, ACTIVE STEP, SLIDE, STEP JUMP Sequence step resolution Quarter note, eighth note, sixteenth note CV OUT pitch Linear, Minor, Major, Chromatic CV OUT voltage 1 V, 2 V, 5 V (V / Oct), 8 V (Hz / V) GATE OUT polarity + (Positive logic), – (negative logic) SYNC IN / OUT polarity + (Rising), – (falling) Connecting terminal little Bits OUT terminal (mini · monaural · phone · jack)
  • OUT (MIDI OUT) terminal (mini · stereo · phone · jack)
  • CV – A OUT – GATE terminal (mini · monaural phone jack, CV OUT: output level 1 V, 2V, 5V, 8V [Hz / V], GATE OUT: output level 10V)
  • CV – B OUT – GATE terminal (Mini · monaural phone jack, CV OUT: output level 1V, 2V, 5V, 8V [Hz / V ], GATE OUT: output level 10V)
  • IN – SYNC – OUT terminal (mini mono phone jack, SYNC IN: maximum input level 20V, SYNC OUT: output level 5V)
  • USB terminal (type B, USB MIDI) Power supply Two AA batteries (Alkaline batteries recommended), or USB bus · power Battery life About 5 hours (when using alkaline dry batteries) External dimensions 193 (W) x 84 (D) x 63 (H) mm

Made in China

Additional information

Model

Arp Odyssey-FSQ1, Arp Odyssey-FSQ2, Arp Odyssey-FSQ3

Related products

Korg ARP Odyssey Duophonic Synthesizer with SQ-1 Sequencer

Add to cart